DL11-55 GEN:2
Gehl: Aerial
Specifications
| Capacities: Capacity at Maximum Forward Reach: | 2,000 lbs. |
| Capacities: Capacity at Maximum Lift Height: | 5,000/5,500 lbs. |
| Capacities: Lift Capacity: | 11,000 lbs. |
| Capacities: Maximum Forward Reach: | 40'9" |
| Capacities: Maximum Lift Height: | 55'1" |
| Capacities: Maximum Reach Below Grade: | 2'10" |
| Components: Brakes: | Oil-Immersed, Disc-type |
| Components: Maximum Travel Speed : | 22.8 mph |
| Components: Parking Brake: | Spring-Applied, Hydraulic Release |
| Components: Selective Steering: | 4-Wheel 2-Wheel Crab |
| Components: Transmission: | 4-Speed Power Shift |
| Engine: Aspiration: | Turbocharged |
| Engine: Manufacturer: | Cummins |
| Engine: Model: | 3.8L QSF Tier IV |
| Engine: Power : | 120 hp |
| Engine: Rated Speed: | 2,500 rpm |
| General Specifications: Approximate Weight: | 28,460 lbs. |
| General Specifications: Frame Leveling - Left/Right: | 10°/10° |
| General Specifications: Fuel Capacity: | 30 gal. |
| General Specifications: Ground Clearance: | 16" |
| General Specifications: Length - Less Forks: | 20'10" |
| General Specifications: Overall Height: | 7'11" |
| General Specifications: Recommended Tire Type: | 14.00 x 24 G2 12-ply |
| General Specifications: Turning Radius: | 12'2" |
| General Specifications: Wheelbase: | 10'8" |
| General Specifications: Width: | 8'3" |
| Hydraulics: Auxiliary Relief Pressure: | 2,500 psi |
| Hydraulics: Hydraulic Reservoir Capacity : | 45 gal. |
| Hydraulics: Main Relief Pressure : | 3,000 psi |
| Hydraulics: Pump Type: | Open-Center, Dual-Section |
| Hydraulics: Total Capacity : | 43 gpm |
| Load Chart: : | 4,000 lbs. |
| Load Chart: : | 500 lbs. |
| Load Chart: : | 7,000 lbs. |
| Load Chart: : | 9,000 lbs. |
| Load Chart: : | 5,000 lbs. |
| Load Chart: : | 1,000 lbs. |
| Load Chart: : | 250 lbs. |
| Load Chart: : | 3,000 lbs. |
| Loader Performance: Breakout Force: | N/A |
- Rifled bushings in key areas
- Exterior boom hose routings for easy access.
- Industry loading job site maneuverability with a 12' 2" turning radius.
- Rear axle stabilization system locks the rear axle to the frame if the parking brake is engaged, if the boom is raised 60 degrees or higher, or if the PWP System is activated.
- 10-degree frame tilt in both directions.
- Hydraulic main control valve in back door.
- Easy access to hydraulic oil and transmission reservoirs.
- Two-wheel, four-wheel, crab steering standard.
- Powershift transmission with four forward and two reverse gears, with a 2-year/2,000-hour warranty.
- Remote Boom Control can raise/lower and extend/retract the boom, as well as start/stop the engine from the work platform or outside the cab.
- Un-matched panoramic visibility increases work-site safety and operator productivity and reduces operator fatigue.
- Double universal joints for tight turn radius without applying stress on the axle.
- Three steering modes – 4-wheel, 2-wheel and crab – enhance maneuverability and are easily changed by the flip of a switch.
- Standard pneumatic tires.
- Engine shutdown protection feature allows 30-seconds of run time for moving the unit to a safe location for loading or repair.
- Standard centrifugal pre-cleaner and two-stage air cleaner.
- Choice of Dual-Function or Tri-Function pilot-operated joysticks that allow operators precise movement of heavy loads
- Lockable, two-piece cab door for security, communication and cross-ventilation.
- Standard lockable storage compartment for service items, such as work gloves, tools, blueprints and more.
- ROPS and FOPS certified operator's compartment.
- Personnel Work Platform System allows the use of ANSI/ITSDF B56.6-compliant personnel work platforms for safety and efficiency.
- Transmission and hydraulics easily accessed through large hinged panel.
- Choice of canopy or cab with heating and defrosting systems standard (air-conditioning optional).
DL7/DL9/DL11/DL12 Parts Manual PDF, 7.01 MB
More information available
